The Gem and Jewelry World's foremost Resource on The Internet.
Re: [Orchid] Sizing ring with bezel-set stone  
  [Thread Prev] [Message Prev]      [Date Index]   [Thread Index]      [Message Next] [Thread Next]
From: Tpdooley
Date: Thu Jul 22 19:24:01 1999
 
     
========[ Invite a Friend - http://www.ganoksin.com/invite.htm  ]========


Hello Linda!

    There are a few products out there for heat sink purposes. What
    you found is prevailing jewelers' technique, I would say.
    However, many jewelers do these type of sizings in their
    fingers. Sure it gets hot; your fingers can take 140 degrees for
    a few seconds too. Your hot water  AT  your tap is probably close
    to that. If you haven't done it or seen it done, try and get an
    experienced craftsman to show you. 

    If you want to do it yourself, here goes. Coat the ring with
    boric acid dip. Let cool. Create a little tension in the ring,
    and slip a piece of solder between the seem. The full length of
    the seem. You can place the solder on top of the seem if you'd
    rather not create tension. Hold it in your thumb and two fingers
    and wet the stone and your fingers in cold water. You did flux
    it, right? Use a large tip with a hole about 1.2 mm or so. So
    you can generate a large hot flame. Without seeing the piece
    there ids no way to judge the flame size or intensity. Generally
    the flame is 5 to 8 inches long, and an oxidizing flame. If you
    use too much oxygen, therefore, more temp, you could fudge
    (melt) the area. You could also burn your flux, therefore
    eliminating its' assistance in flowing the solder. You do have
    several advantages, you have cold water right there. You can
    quench if it gets to hot and reflux. 

    If were talking silver, that requires more heat and is more
    difficult. Yuk! 

    If you had a jeweler who could show you that would be best. 

										
	Good luck,					
	Tim


____________________________________________________________________
T h e   O r c h i d   L i s t
Open Electronic Forum for Jewelry Manufacturing Methods and Procedures
____________________________________________________________________
Orchid FAQ:
~ http://www.ganoksin.com/orchid/faq.htm
Orchid Archives:
~ http://www.ganoksin.com/orchid/archive
Orchid Galleries:
~ http://www.ganoksin.com/orchid/gallery.htm
Invite a Friend:
~ http://www.ganoksin.com/invite.htm
____________________________________________________________________
Tips From The Jeweler's Bench - Article Archive
~ http://www.ganoksin.com/borisat/tip_sear.htm
The Jeweler's Selected Bibliography List
~ http://www.ganoksin.com/jewelry-books
Buy Orchid Jewelry:
~ http://www.ganoksin.com/shop
____________________________________________________________________
-Unsubscribe:
-Email: orchid-request AT ganoksin.com Body=unsubscribe subject=blank
____________________________________________________________________


  Click to Visit  
     
  Navigate:  
   
  Orchid Resources:  
   Join & Post
 Invite a friend to join Orchid
 F.A.Q
 Galleries
 BenchExchange
 Orchid Message Archives [Subject Index] [Date Index]

Ganoksin now offers a number of ways for you to stay on top of the latest from Orchid!

  1. My Yahoo - Do you have a My Yahoo page? If so, you can easily read the latest Orchid posts on your personalized page by adding this feed:Add Orchid to My Yahoo!
  2. Add Orchid to myGoogle Add to my Google
  3. Read Orchid with NewsGator and Microsoft Outlook Add Orchid to Your  NewsGator
Support Orchid! - If you believe in what we're doing, you can help!

 
     
     

© Copyright 1996 - 2008, The Ganoksin Project